CFM Ventilation Hood GEF10 User Manual

INSTALLATION & MAINTENANCE GUIDE  
SEF, PEF & GEF EXHAUST FANS DIRECT DRIVE  
READ AND SAVE THESE INSTRUCTIONS FOR FUTURE REEFERENCE  
SEF SHUTTER MOUNT FAN  
PEF PANEL MOUNT FAN  
GEF GUARD MOUNT FAN  
CAUTION! THESE FANS ARE DESIGNED FOR GENERAL  
VENTILATION USE ONLY. DO NOT USE TO EXHAUST CORRO-  
SIVE, HAZARDOUS OR EXPLOSIVE MATERIALS AND VAPORS.  
ASSEMBLY INSTRUCTIONS  
MODELS SEF-10 THROUGH SEF-24  
Contents: Pre-assembled guard mount fan, shutter, shutter  
mounting hardware kit, package of mounting screws.  
BEFORE INSTALLATION  
WARNING! TO REDUCE THE RISK OF FIRE, ELECTRICAL  
SHOCK, OR INJURY TO PERSONS, PLEASE OBSERVE THE  
FOLLLOWING SAFETY PRECAUTIONS:  
To mount shutter to fan assembly:  
1. Shutter mounting hardware kit includes: 4 rubber vibration  
isolators, 4 nylon inserts, 4 screws (#12 x 1”) and 4 rubberized  
washers.  
2. Insert screws into washers - rubber side down.  
3. Place nylon inserts into square holes of corner gussets at  
rear of shutter.  
4. Place shutter face down (gusset side up). Center vibration  
isolators over nylon inserts.  
5. Place fan assembly on shutter so that wire hooks on fan  
guard are centered over vibration isolators and nylon  
inserts. Junction box must be positioned at bottom with  
shutter blades opening upwards.  
1. This fan has rotating parts! Turn impeller by hand to ensure  
that it rotates freely.  
2. Ensure that electrical service to fan is locked in the  
“OFF” position to prevent power from being switched on  
accidentally. When the service disconnecting means  
cannot be locked, securely fasten a prominent warning  
device such as a tag to service panel.  
3. Do not re-establish power supply until fan and activation  
device are completely installed.  
4. Installation work, including electrical wiring, must be  
performed by a qualified person in accordance with all  
applicable codes and standards, including local fire codes.  
5. Check voltage at fan to see that it corresponds to fan motor  
nameplate rating.  
6. Secure fan assembly to shutter using screws and washers.  
7. Ensure that fasteners are snug. Do not over tighten to  
avoid stripping nylon inserts.  
MODEL SEF-30  
6. Fan is intended to be hard wired to a properly rated  
electrical circuit, and must be properly grounded. Do  
not use an extension cord.  
Contents: Pre-assembled guard mount fan, shutter, shutter  
mounting hardware kit, package of mounting screws.  
7. Fan motor is equipped with thermal overload protection,  
which causes fan to shut off automatically if motor overheats.  
If this should happen, immediately disconnect and lock power  
supply to fan. Do not attempt to workk on fan without discon-  
necting power supply; fan may restart without warning!  
8. Fan should not be turned on and off rapidly.  
9. Do not use fan with a solid state speed control device.  
10. Do not allow fan to become wet or damp.  
To mount shutter to fan assembly:  
1. Shutter mounting hardware kit includes: 4 rubber vibration  
isolators, 8 rubber inserts, 8 screws (#8-32 x 11/2”) and 8  
rubberized washers.  
2. Insert screws into washers - rubber side down.  
3. Place rubber inserts into round holes of corner gussets at  
rear of shutter. It may be necessary to twist and push or tap  
lightly to seat rubber inserts properly.  
11. Do not block air intake or exhaust from fan.  
12. Do not allow foreign objects to enter fan and come in  
contact with fan blades.  
4. Place shutter face down (gusset side up). Center vibration  
isolators over rubber inserts.  
5. Place fan assembly on shutter so that wire hooks on fan  
guard are centered over vibration isolators and nylon  
inserts. Junction box must be positioned at bottom with  
shutter blades opening upwards.  
6. Secure fan assembly to shutter using screws and washers.  
7. Ensure that fasteners are snug. Do not over tighten to  
avoid pulling out rubber inserts.  
SPEED SELECTOR SWITCH  
Fan is equipped with either a 2-speed or 3-speed pull chain switch,  
allowing user to select desired airflow. Pulling a speed selector  
switch repeatedly will cause fan speed to cycle as follows:  
2-Speed Switch:  
OFF – FIRST SPEED – OFF – SECOND SPEED – OFF  
MODELS PEF-10 THROUGH PEF-30  
Contents: Pre-assembled panel mount fan.  
3-Speed Switch:  
OFF – HIGH – MEDIUM – LOW – OFF  
MODELS GEF-10 THROUGH GEF-30  
Contents: Pre-assembled guard mount fan.  
 

Billy Goat Vacuum Cleaner HTR1803V User Manual
Blackberry Cell Phone MAT 41363 001 page
Black Box Network Card IC266A User Manual
Blodgett Convection Oven CNVX 14 User Manual
Brocade Communications Systems Network Router 53 1002373 02 User Manual
Chamberlain Garage Door Opener 2000UK User Manual
Chauvet Landscape Lighting fx12 User Manual
Chief Manufacturing Indoor Furnishings FSA 1005 User Manual
Chief Manufacturing Stereo System side shelf for the steel elite converta rack User Manual
Cisco Systems Network Card WS C2950 12 User Manual