User Manual
MINIMON MON800
Ultra-Compact Stereo Monitor Matrix Mixer with Talkback Mic
3
MINIMON MON800 User Manual
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus
near water.
15. The apparatus shall be connected to
a MAINS socket outlet with a protective
earthing connection.
16. Where the MAINS plug or an
appliance coupler is used as the
disconnect device, the disconnect device
shall remain readily operable.
Important Safety
Instructions
6. Clean only with dry cloth.
Terminals marked with this
symbol carry electrical
current of sufficient
7. Do not block any ventilation
openings. Install in accordance with the
manufacturer’s instructions.
8. Do not install near any heat sources
such as radiators, heat registers, stoves,
or other apparatus (including amplifiers)
that produce heat.
9. Do not defeat the safety purpose
of the polarized or grounding-type plug.
A polarized plug has two blades with
one wider than the other. A grounding-
type plug has two blades and a third
grounding prong. The wide blade or the
third prong are provided for your safety.
If the provided plug does not fit into
your outlet, consult an electrician for
replacement of the obsolete outlet.
10. Protect the power cord from being
walked on or pinched particularly at
plugs, convenience receptacles, and the
point where they exit from the apparatus.
magnitude to constitute risk of electric
shock. Use only high-quality professional
speaker cables with ¼" TS or twist-
locking plugs pre-installed. All other
installation or modification should be
performed only by qualified personnel.
LEGAL DISCLAIMER
TECHNICAL SPECIFICATIONS AND
APPEARANCES ARE SUBJECT TO CHANGE
WITHOUT NOTICE AND ACCURACY IS NOT
GUARANTEED. BEHRINGER IS PART OF
THE MUSIC GROUP (MUSIC-GROUP.COM).
ALL TRADEMARKS ARE THE PROPERTY
OF THEIR RESPECTIVE OWNERS.
This symbol, wherever it
appears, alerts you to the
presence of uninsulated
dangerous voltage inside the enclosure -
voltage that may be sufficient to
constitute a risk of shock.
MUSIC GROUP ACCEPTS NO LIABILITY
FOR ANY LOSS WHICH MAY BE
This symbol, wherever it
appears, alerts you to
important operating and
maintenance instructions in the
accompanying literature. Please read
the manual.
SUFFERED BY ANY PERSON WHO RELIES
EITHER WHOLLY OR IN PART UPON
ANY DESCRIPTION, PHOTOGRAPH
OR STATEMENT CONTAINED HEREIN.
COLORS AND SPECIFICATIONS MAY
VARY FROM ACTUAL PRODUCT.
11. Use only attachments/accessories
specified by the manufacturer.
Caution
To reduce the risk of electric
shock, do not remove the
MUSIC GROUP PRODUCTS ARE SOLD
THROUGH AUTHORIZED FULLFILLERS
AND RESELLERS ONLY. FULLFILLERS
AND RESELLERS ARE NOT AGENTS OF
MUSIC GROUP AND HAVE ABSOLUTELY
NO AUTHORITY TO BIND MUSIC GROUP
BY ANY EXPRESS OR IMPLIED
UNDERTAKING OR REPRESENTATION.
THIS MANUAL IS COPYRIGHTED.
NO PART OF THIS MANUAL MAY BE
REPRODUCED OR TRANSMITTED IN ANY
FORM OR BY ANY MEANS, ELECTRONIC
OR MECHANICAL, INCLUDING
12. Use only with
the cart, stand,
top cover (or the rear section). No user
serviceable parts inside. Refer servicing
to qualified personnel.
tripod, bracket,
or table specified by
the manufacturer,
Caution
or sold with
To reduce the risk of fire or
the apparatus. When a cart is used,
use caution when moving the cart/
apparatus combination to avoid injury
from tip-over.
electric shock, do not expose
this appliance to rain and moisture.
The apparatus shall not be exposed to
dripping or splashing liquids and no
objects filled with liquids, such as vases,
shall be placed on the apparatus.
13. Unplug this apparatus during
lightning storms or when unused for long
periods of time.
PHOTOCOPYING AND RECORDING OF
ANY KIND, FOR ANY PURPOSE, WITHOUT
THE EXPRESS WRITTEN PERMISSION OF
MUSIC GROUP IP LTD.
Caution
14. Refer all servicing to qualified
service personnel. Servicing is required
when the apparatus has been damaged
in any way, such as power supply cord or
plug is damaged, liquid has been spilled
or objects have fallen into the apparatus,
the apparatus has been exposed to rain
or moisture, does not operate normally,
or has been dropped.
These service instructions
are for use by qualified
ALL RIGHTS RESERVED.
service personnel only. To reduce the
risk of electric shock do not perform any
servicing other than that contained in the
operation instructions. Repairs have to be
performed by qualified service personnel.
© 2012 MUSIC Group IP Ltd.
Trident Chambers, Wickhams Cay,
P.O. Box 146, Road Town, Tortola,
British Virgin Islands
4
MINIMON MON800 User Manual
LIMITED WARRANTY
carefully. Registering your purchase and
equipment with us helps us process your
which is not the country for which
the product was originally developed
§ 1 Warranty
repair claims quicker and more efficiently. and manufactured, this modification/
This limited warranty is valid only
(1)
Thank you for your cooperation!
adaptation shall not be considered a
defect in materials or workmanship.
This limited warranty does not cover
any such modification/adaptation,
regardless of whether it was carried out
properly or not. Under the terms of this
limited warranty, MUSIC Group shall not
be held responsible for any cost resulting
from such a modification/adaptation.
if you purchased the product from a
MUSIC Group Authorized Reseller in the
country of purchase. A list of authorized
resellers can be found on BEHRINGER’s
website behringer.com under “Where to
Buy“, or you can contact the MUSIC Group
office closest to you.
§ 3 Return materials
authorization
To obtain warranty service,
(1)
please contact the retailer from
whom the equipment was purchased.
Should your MUSIC Group Authorized
Reseller not be located in your vicinity,
you may contact the MUSIC Group
Authorized Fulfiller for your country
listed under “Support” at behringer.com.
If your country is not listed, please check
if your problem can be dealt with by our
“Online Support” which may also be
found under “Support” at behringer.com.
Alternatively, please submit an online
warranty claim at behringer.com BEFORE
returning the product. All inquiries must
be accompanied by a description of the
problem and the serial number of the
product. After verifying the product’s
warranty eligibility with the original
sales receipt, MUSIC Group will then
issue a Return Materials Authorization
(“RMA”) number.
MUSIC Group* warrants the
(2)
mechanical and electronic components
of this product to be free of defects in
material and workmanship if used under
normal operating conditions for a period
of one (1) year from the original date
of purchase (see the Limited Warranty
terms in § 4 below), unless a longer
minimum warranty period is mandated
by applicable local laws. If the product
shows any defects within the specified
warranty period and that defect is
This limited warranty covers only
(3)
the product hardware. It does not cover
technical assistance for hardware or
software usage and it does not cover
any software products whether or not
contained in the product. Any such
software is provided “AS IS” unless
expressly provided for in any enclosed
software limited warranty.
This limited warranty is invalid if the
(4)
factory-applied serial number has been
altered or removed from the product.
not excluded under § 4, MUSIC Group
shall, at its discretion, either replace or
repair the product using suitable new or
reconditioned product or parts. In case
MUSIC Group decides to replace the
entire product, this limited warranty
shall apply to the replacement product
for the remaining initial warranty period,
i.e., one (1) year (or otherwise applicable
minimum warranty period) from the date
of purchase of the original product.
Free inspections and maintenance/
(5)
repair work are expressly excluded from
this limited warranty, in particular,
if caused by improper handling of the
product by the user. This also applies
to defects caused by normal wear and
tear, in particular, of faders, crossfaders,
potentiometers, keys/buttons,
guitar strings, illuminants and
Subsequently, the product must be
(2)
returned in its original shipping carton,
together with the return authorization
number to the address indicated by
MUSIC Group.
similar parts.
Upon validation of the warranty
(3)
Shipments without freight prepaid
(3)
Damage/defects caused by the
(6)
claim, the repaired or replacement
product will be returned to the user
freight prepaid by MUSIC Group.
will not be accepted.
following conditions are not covered by
this limited warranty:
§ 4 Warranty Exclusions
•
•
•
improper handling, neglect or
failure to operate the unit in
compliance with the instructions
given in BEHRINGER user or
service manuals;
This limited warranty does not cover
Warranty claims other than those
(1)
(4)
consumable parts including, but not
limited to, fuses and batteries. Where
applicable, MUSIC Group warrants the
valves or meters contained in the product
to be free from defects in material and
workmanship for a period of ninety (90)
days from date of purchase.
indicated above are expressly excluded.
PLEASE RETAIN YOUR SALES RECEIPT.
IT IS YOUR PROOF OF PURCHASE COVERING
YOUR LIMITED WARRANTY. THIS LIMITED
WARRANTY IS VOID WITHOUT SUCH
PROOF OF PURCHASE.
connection or operation of the
unit in any way that does not
comply with the technical or safety
regulations applicable in the
§ 2 Online registration
This limited warranty does not cover
(2)
country where the product is used;
the product if it has been electronically
or mechanically modified in any way.
If the product needs to be modified
or adapted in order to comply with
applicable technical or safety standards
on a national or local level, in any country
Please do remember to register your
new BEHRINGER equipment right after
your purchase at behringer.com under
“Support” and kindly read the terms
and conditions of our limited warranty
damage/defects caused by acts of
God/Nature (accident, fire, flood,
etc) or any other condition that is
beyond the control of MUSIC Group.
5
MINIMON MON800 User Manual
Any repair or opening of the
§ 7 Limitation of liability
(7)
unit carried out by unauthorized
personnel (user included) will void the
limited warranty.
This limited warranty is the complete
and exclusive warranty between you
and MUSIC Group. It supersedes all other
written or oral communications related
to this product. MUSIC Group provides no
other warranties for this product.
If an inspection of the product by
(8)
MUSIC Group shows that the defect in
question is not covered by the limited
warranty, the inspection costs are
payable by the customer.
§ 8 Other warranty rights
and national law
Products which do not meet the
terms of this limited warranty will
(9)
This limited warranty does not
(1)
exclude or limit the buyer’s statutory
rights as a consumer in any way.
be repaired exclusively at the buyer’s
expense. MUSIC Group or its authorized
service center will inform the buyer of
any such circumstance. If the buyer fails
to submit a written repair order within
6 weeks after notification, MUSIC Group
will return the unit C.O.D. with a separate
invoice for freight and packing. Such costs
will also be invoiced separately when the
buyer has sent in a written repair order.
The limited warranty regulations
(2)
mentioned herein are applicable unless
they constitute an infringement of
applicable mandatory local laws.
This warranty does not detract from
(3)
the seller’s obligations in regard to any
lack of conformity of the product and any
hidden defect.
MUSIC Group Authorized Resellers
(10)
§ 9 Amendment
do not sell new products directly in online
auctions. Purchases made through an
online auction are on a “buyer beware”
basis. Online auction confirmations
or sales receipts are not accepted for
warranty verification and MUSIC Group
will not repair or replace any product
purchased through an online auction.
Warranty service conditions are subject
to change without notice. For the
latest warranty terms and conditions
and additional information regarding
MUSIC Group’s limited warranty,
please see complete details online at
behringer.com.
* MUSIC Group Macao Commercial Offshore
Limited of Rue de Pequim No. 202-A,
Macau Finance Centre 9/J, Macau,
§ 5 Warranty transferability
This limited warranty is extended
exclusively to the original buyer
including all MUSIC Group companies
(customer of authorized reseller) and is
not transferable to anyone who may
subsequently purchase this product.
No other person (reseller, etc.) shall be
entitled to give any warranty promise on
behalf of MUSIC Group.
§ 6 Claim for damage
Subject only to the operation of
mandatory applicable local laws,
MUSIC Group shall have no liability to
the buyer under this warranty for any
consequential or indirect loss or damage
of any kind. In no event shall the liability
of MUSIC Group under this limited
warranty exceed the invoiced value of
the product.
6
MINIMON MON800 User Manual
1.1.2 Initial operation
1. Introduction
Be sure that there is enough space around the unit for cooling.
To avoid overheating, do not place the MON800 on top of power amps
or near radiators, etc.
The MON800 features a clearly structured input section with four
selectable and mixable stereo inputs, as well as a high-precision,
6-digit LED output level meter for accurate level control. It also
includes a powerful headphones output with its own volume control,
plus three selectable stereo loudspeaker outputs with separate
volume controls for optimum adjustment.
◊
To power the MON800, use only the power supply unit that is
delivered with your equipment.
◊
Please ensure that the unit is installed and operated only by
people qualified to do so. During installation and operation
the user must have sufficient electrical contact to earth.
Electrostatic discharge may affect the operation of the unit.
The Mute and Dim functions as well as a mono switch for checking
signals for mono compatibility (phase) give the MON800 even
greater flexibility. The integrated talk-back section with its
built-in microphone provides you with a full set of routing options.
High-quality potentiometers and backlit switches ensure long-term
reliability. What is more, our extremely low-noise operational
amplifiers are synonymous for outstanding audio quality.
1.1.3 Online registration
Please register your new BEHRINGER equipment right after your
conditions of our warranty carefully.
With the MON800 you have your music productions totally
under control!
Should your BEHRINGER product malfunction, it is our intention
to have it repaired as quickly as possible. To arrange for warranty
service, please contact the BEHRINGER retailer from whom the
equipment was purchased. Should your BEHRINGER dealer not
be located in your vicinity, you may directly contact one of our
subsidiaries. Corresponding contact information is included in
the original equipment packaging (Global Contact Information/
European Contact Information). Should your country not be listed,
please contact the distributor nearest you. A list of distributors can be
found in the support area of our website (http://behringer.com).
1.1 Before you get started
1.1.1 Shipment
Your MON800 was carefully packed at the assembly plant to assure
secure transport. Should the condition of the cardboard box
suggest that damage may have taken place, please inspect the unit
immediately and look for physical indications of damage.
◊
Damaged equipment should NEVER be sent directly to us.
Please inform the dealer from whom you acquired the
unit immediately as well as the transportation company
from which you took delivery. Otherwise, all claims for
replacement/repair may be rendered invalid.
Registering your purchase and equipment with us helps us process
your repair claims more quickly and efficiently.
Thank you for your cooperation!
◊
◊
◊
Please always use the original packaging to avoid damage
due to storage or shipping.
Never let unsupervised children play with the MON800 or
with its packaging.
Please dispose of all packaging materials in an
environmentally friendly fashion.
7
MINIMON MON800 User Manual
2. MON800 Quick-Start Set-Up
Fig. 2.1: MON800 quick-start set-up
Please follow the instructions below to set up the MON800 as a
monitor unit with different speakers in your studio.
•
Switch off the A speakers and activate the B speakers. Use SPK
B + C LEVEL to adjust a volume level that is roughly the same as
the A speakers volume.
•
Connect your computer or any other line-level source to the MIX
IN A connectors on the MON800.
•
•
Switch between the two pairs of speakers to check the volume
levels. Align the volume if necessary.
•
Connect your main monitor speakers to the SPEAKERS OUT A
connectors, and another pair of speakers to the B outputs.
By switching between the two pairs of speakers you can
evaluate your mixes by way of a direct comparison using two
different monitor systems.
•
•
Press the MIX A switch in the SOURCE section.
Use the 2-TR OUT LED display to check the signal level. If the CLIP
LED lights up, please reduce the input signal level until it settles
between the -6 dB and +6 dB markings.
•
The switches A and B allow you to switch the pairs of speakers
on and off. Activate the A speakers and adjust the desired
volume with SPK A LEVEL.
8
MINIMON MON800 User Manual
3. Control Elements and Connections
3.1 Front panel
(4)
(5)
(7) (9) (10)
(1)
(2)
(3)
(6)
(8)
(11) (12)
(13)
Fig. 3.1: Front panel control elements of the MON800
(1) Use the four switches in the SOURCE section to select up to four
input sources (MIX A and B, CD/TAPE C and D) for monitoring
and recording. If desired, several sources can be activated at
the same time. Subsequently, the signals are mixed. Each active
source is indicated by its switch lighting up.
(7) With the MUTE switch you can disable all loudspeaker and
headphones outputs.
(8) The MONO switch switches all monitor paths to mono. This is
useful, in particular, when you want to check your mix for
mono compatibility. Extreme panorama settings and excessive
use of effects, such as chorus, phaser and flanger in the
stereo mix can lead to signal cancellations during playback in
mono. Such phase problems can easily be detected with the
MONO switch.
(2) The two LED displays are for monitoring the output level of the
2-TRACK OUT outputs. They comprise 6 LEDs each. When the
CLIP LED lights up, this indicates that distortion may occur.
In this case, please reduce the levels of the signal sources
connected to the input of the MON800.
(9) The DIM switch lowers the level of the monitor paths by -20 dB.
This allows you, for example, to talk to somebody while mixing
without losing track of the recording.
(3) A pair of headphones with a 1" TRS connector (e.g. BEHRINGER
HPS5000) can be connected to the PHONES jack. This output is
wired in parallel with the rear-panel output jack (15), so that up
to two headphones can be used at the same time.
◊
Switches (7) to (9) light up when the corresponding
functions are active. The functions performed by
these switches do not affect the signals of the two
2-TRACK OUT outputs.
(4) With the PHONES LEVEL control you can adjust the
volume for the two headphones jacks on the front or rear
panel respectively.
(10) Use the TALK LEVEL control to adjust the sensitivity of the
◊
The volume on the headphones from the front and rear
panel jacks cannot be adjusted separately.
talk-back microphone.
(11) The talk-back microphone is installed behind the MIC openings.
Speak into the microphone to make announcements which are
then routed to the recording devices connected to the 2-TRACK
OUT outputs. This allows you to record the numbers or names
of different recording takes, for example, and thus maintain a
clear overview of your work. Additionally, the microphone can
be used to communicate with the musicians who can hear your
voice on their headphones.
(5) SPK A LEVEL governs the volume level of the SPEAKERS OUT A
outputs (18). SPK B + C LEVEL allows you to set the volume for
outputs B and C (17) simultaneously.
(6) Use the switches A/B/C ON to switch the speakers A, B and C on
and off. While mixing it is advisable to listen to your production
over at least two different pairs of speakers, so as to get an
objective impression of your mix. If you wish to switch between
different monitoring systems, press the corresponding switches
of the active and of the inactive speaker pair one after the
other. Active speakers are always indicated by their switches
lighting up.
9
MINIMON MON800 User Manual
(12) The TALK TO CUE/PHONES/SPK A and TALK TO 2-TR OUT
buttons determine where the talk-back microphone signal is
routed to. With the TALK TO CUE/PHONES/SPK A button the
signal is routed to the monitor paths CUE OUT, PHONES, PH and
SPEAKERS OUT A. In this case, the DIM function (9) is activated
automatically to avoid feedback. The TALK TO 2-TR OUT button
allows you to route the signal via the two 2-TRACK OUT outputs
to the recording devices connected.
(13) The
switch turns your MINIMON MON800 on and off.
◊
Attention: The
switch does not fully disconnect
the unit from the mains. To disconnect the unit from
the mains, pull out the main cord plug or appliance
coupler. When installing the product, ensure the plug or
appliance coupler is readily operable. Unplug the power
cord completely when the unit is not used for prolonged
periods of time.
◊
Hold the button down as long as you wish to speak.
3.2 Rear panel
(15)
(14)
(16)
(17)
(18) (19) (20)
(21)
(22)
Fig. 3.2: Rear panel connectors of the MON800
(14) The MON800 is connected to the mains using a 2-pole POWER
connector jack. A matching mains adaptor is included with
the unit.
(19) CUE OUT is an additional output, which you can use to route
the MINIMON signals to other devices, such as an additional
headphones amp (e.g. BEHRINGER MINIAMP AMP800)
(see chapter 4.1).
◊
To avoid damage to your COM800 always use the mains
adaptor supplied with the unit.
◊
The CUE OUT level cannot be changed on the MON800.
(15) A second pair of headphones can be connected to the PH jack.
This connector is wired in parallel with the front-panel jack (3).
(20) The two 2-TRACK OUT jacks are wired in parallel and carry the
same signals. Use the 1" or cinch outputs, depending on the
recording device used.
(16) The TB jack is used to connect a single footswitch.
This footswitch allows hands-free talking and the use of the
talk-back button (12) (TALK TO CUE/PHONES/SPK A) at the
same time.
(21) Use the CD/TAPE IN jacks C and D to connect playback devices,
such as a computer, CD/MD or cassette player.
(22) The MIX IN jacks A and B are for connecting the main signal
sources (e.g. mixing console, audio card, etc.) using 1" plugs.
Mono signals must be connected to the L jacks.
◊
Hold the button down as long as you wish to speak.
(17) Two pairs of loudspeakers can be connected to the
SPEAKERS OUT B and C jacks. Since the levels of both pairs
(B and C) can only be adjusted together on the MON800, it’s a
good idea to connect one speaker pair to output B and an
additional sub-woofer to output C (see chapter 4.1).
The SERIAL NUMBER of your MON800 can be found on the bottom
side of the unit.
(18) Connect your main monitor speakers to the
SPEAKERS OUT A jack.
◊
The loudspeaker outputs are designed for the
connection of active systems or an external amplifier
with passive speakers.
10 MINIMON MON800 User Manual
4. Application Examples
The MINIMON gives you a great number of monitoring options,
which you would otherwise find only in costly mixing consoles .
4.1 The MINIMON in a recording
environment
A typical example of how to use the MON800 is the computer-based
Therefore, an ideal field of application is to use the MON800 to control production of music with additional instrument or voice recordings.
and distribute signals in a recording environment. However, with its
flexibility the MON800 is also the ideal tool for P.A. applications.
The following illustration shows an example of how to wire the unit in
such an environment.
Fig. 4.1: The MON800 in a typical computer-based recording environment
As a central element of this configuration, the computer is connected
via its audio card to the MIN IN A or B jacks (22) of the MON800.
Additional sound modules, which are connected to the computer,
for example, via MIDI, can be wired to the remaining inputs
are used as secondary speakers, so that it is possible to evaluate a mix
over less powerful systems. A sub-woofer is an ideal complement
to such a pair of speakers and should be connected to output C (17),
since the levels of both outputs can be adjusted simultaneously.
(depending on the respective connecting plugs). Playback devices
(CD, MD, etc.) should be connected to the CD/TAPE IN jacks (21).
Connect your main monitor speakers to the SPEAKERS OUT A jacks (18).
Output B (17) is for a second pair of speakers. Often, smaller systems
If required, you can also connect a third pair of speakers, ideally with
an adjustable amplifier stage, so that you can set the volume of the
speaker pair C independently of the SPK LEVEL B + C control (5).
11 MINIMON MON800 User Manual
◊
The speaker outputs of the MINIMON provide line-level
signals. Passive loudspeaker systems must be connected via
an external integrated amplifier. Active loudspeakers have
an amplifier built in and can therefore be connected directly
to the MINIMON outputs.
4.2 Using the MINIMON for signal
distribution in simple P.A. applications
The MINIMON can also be used for small P.A. systems,
for example, in cafés and galleries. In this case, the three loudspeaker
outputs (17) and (18) can be used for three pairs of speakers set up
in several rooms. The inputs C and D (21) of the MINIMON can be
connected directly to consumer equipment, such as CD/MD/
cassette players or a radio tuner. If necessary, the built-in talk-back
microphone (11) allows you to make announcements for your guests.
With an additional set of headphones you can pre-listen to the input
signals you wish to play back via the audio system. The following
illustrations shows a possible wiring scheme.
The two headphones connectors (3) and (15) allow you to check your
mix with a pair of headphones or route a monitor signal to one of the
musicians. If you want to record several musicians, use the CUE OUT jack
(19) for the connection of a headphones amp (e.g. BEHRINGER MINIAMP
AMP800). In this way, each musician can set the volume of his
headphones separately on the headphones amplifier.
Using a footswitch connected to the TB jack (16) you can activate the talk-
back microphone and route the microphone signal to the monitor paths.
A recording device, such as a DAT or CD recorder, can be connected to
the 2-TRACK OUT outputs (20).
Fig. 4.2: Using the MON800 for signal distribution in small P.A. systems
12 MINIMON MON800 User Manual
5. Audio Connections
5.2 Footswitch connection
There are various ways to integrate the MON800 into your set-up.
The MINIMON features a jack for the connection of a footswitch.
Depending on the application in question, you will need different sets Here, you can connect any commercially available footswitch with
of connecting cables. The cables to use are described below.
a 1" TS connector. As some footswitch models on the market have
a different polarity, please be sure to use one that is appropriately
wired. The correct wiring is shown in the illustration below.
5.1 Connection with 1" or cinch cables
Please use standard 1" or cinch cables to connect the MINIMON to
other equipment. These cables have a 1" or cinch connector at each
end. Connect the inputs and outputs of the MON800 to the respective
connectors of the other devices.
Fig. 5.1: Wiring diagram of a hi-fi cinch cable
tip
signal
sleeve
Fig. 5.3: Wiring of a 1" TS connector for footswitch connection
ground/shield
5.3 Headphones connection
The MINIMON has two jacks for headphones. Here, you can connect
any standard pair of stereo headphones with a 1" TRS connector.
For 3.5-mm plugs you need an appropriate adaptor. The correct
wiring diagram is shown in the illustration below.
tip
sleeve
strain relief clamp
strain relief clamp
sleeve
tip
sleeve
ground/shield
Fig. 5.4: Wiring of a 1" TRS headphones connector
tip
signal
Fig. 5.2: Unbalanced cable with 1" TS connectors
13 MINIMON MON800 User Manual
6. Specifications
Mix In A + B
System Specifications
Frequency response
Dynamic range
Distortion (THD)
Crosstalk
10 Hz to 80 kHz, 3 dB
112 dB, 20 Hz to 20 kHz
0,005% typ. @ +4 dBu
-75 dB @ 1 kHz
Type
1" TS connectors
Impedance
approx. 10 kΩ unbalanced
approx. 20 kΩ balanced
Max. input level
15 dBu
Signal-to-noise ratio
102 dBu @ +4 dBu,
A-weighted
CD/Tape In C + D
Type
RCA connectors
approx. 10 kΩ
15 dBu
Power Supply
Impedance
Max. input level
Mains connection
external power supply,
9 V~, 750 mA
2-Track Out A + B
Mains Voltage
USA/Canada
U.K./Australia
China
120 V~, 60 Hz
240 V~, 50 Hz
220 V~, 50 Hz
230 V~, 50 Hz
100 V~, 50 - 60 Hz
approx. 6 W
Type
1" TS connectors /
RCA connectors
Impedance
approx. 150 Ω (TS),
approx. 150 Ω (RCA)
Europe
Max. output level
15 dBu
Japan
Cue Out
Power consumption
Type
1" TS connectors
min. 150 Ω
15 dBu
Dimensions/Weight
Impedance
Max. output level
DIMENSIONS (H x W x D)
Weight
approx. 48 x 120 x 242.6 mm
approx. 0.77 kg
Phones
BEHRINGER makes every effort to ensure the highest standard of quality. Necessary modifications
are carried out without notice. Thus, the specifications and design of the device may differ from the
information given in this manual.
Type
1" TRS connector
(on front/back)
Impedance
min. 100 Ω
Max. output level
10 dBu / 100 Ω (70 mW)
Speakers Out A
Type
1" TS connectors
min. 150 Ω
15 dBu
Impedance
Max. output level
Speakers Out B + C
Type
RCA connectors
min. 150 Ω
15 dBu
Impedance
Max. output level
14 MINIMON MON800 User Manual
7. Other Mini Products
The MINIMON belongs to the MINI suite of BEHRINGER products,
which can operate together and are introduced below:
MINIFEX FEX800
Ultra-compact 9.5" stereo multi-effects processor for studio and
stage applications
•
16 awesome FX presets in 24-bit/48 kHz resolution including
reverb, delay, chorus, flanger, phaser, rotary speaker,
pitch shifter and multi-effects
•
Intuitive FX Preset control with LED’s indicating the
selected program
MINIAMP AMP800
Ultra-compact 9.5" headphones amplifier system for studio and
stage applications
•
4 totally independent stereo high-power amplifier sections
•
Highest sonic quality with virtually all types of headphones
even at maximum volume
Fig. 7.1: MINI products stack on top of each other
MINIMIC MIC800
Ultra-compact 9.5" microphone modeling preamp for studio and
stage applications
•
High-end preamplifier for all microphone, instrument and
line-level sources. Perfectly complements studio-grade
condenser mics
•
Ultra-flexible Preamp Modeling allows you to quickly optimize
your recordings
MINIFBQ FBQ800
Ultra-compact 9.5" graphic equalizer for studio and stage applications
•
Revolutionary FBQ Feedback Detection System instantly reveals
critical frequencies and can also be used as Audio Analyzer
•
Additional Low Cut filter removes unwanted frequencies,
e. g. floor rumble
MINIMIX MIX800
Ultra-compact 9.5" karaoke machine for studio and stage applications
•
Revolutionary Voice Canceller—effectively eliminates vocals
from any stereo source while retaining most music elements
•
Integrated digital echo/reverb processor in 24-bit/40 kHz
resolution for ultimate vocal enhancement
We Hear You
|