Amana Ventilation Hood UXG7360V User Manual

Wall-Mount Canopy Grill Vent Hood  
PRODUCT MODEL NUMBERS  
PRODUCT DIMENSIONS  
UXG7360V  
UXG7480V  
Vented installations  
12"  
(30.5 cm)  
Electrical: 120-volt, 60-Hz, AC-only, 15-amp fused electrical circuit  
is required.  
LOCATION REQUIREMENTS  
Canopy grill vent hood location should be away from strong draft  
areas, such as windows, doors and strong heating vents.  
Venting methods  
18"  
(45.7 cm)  
This canopy grill vent hood is factory set for venting through the roof  
or through the wall. A 10" (25.4 cm) round vent system is needed for  
installation (not included). The hood exhaust opening is 10" (25.4 cm)  
round.  
4"  
(10.2 cm)  
NOTE: Flexible vent is not recommended. Flexible vent creates back  
pressure and air turbulence that greatly reduce performance. Vent  
system can terminate either through the roof or through the wall. To  
vent through a wall, a 90° elbow is needed.  
30" (76.2 cm)  
36" (91.4 cm)  
48" (121.9 cm)  
24"  
(61.0 cm)  
Rear discharge  
INSTALLATION DIMENSIONS  
A 90° elbow may be installed immediately above the hood.  
Roof Venting  
Wall Venting  
C
C
D
B
A
B
*NOTE:The grill vent hood  
duct cover is designed to add  
12" (30.5 cm) to meet the  
ceiling or soffit height.  
Depending on your model,  
order:  
A
D
X
Part Number W10153151 for  
30" (76.2 cm) models,  
Part Number W10153152 for  
36" (91.4 cm) models,  
Part Number W10153153 for  
48" (121.9 cm).  
IMPORTANT:  
Minimum distance “X”:  
30" (76.2 cm)  
A. Optional decorative duct cover  
B. 10" (25.4 cm) round vent  
C. Roof cap  
D. 10" (25.4 cm) round vent  
transition  
A. Optional decorative duct cover  
B. 10" (25.4 cm) round vent and  
elbow  
C. Wall cap  
D. 10" (25.4 cm) round vent  
transition  
Suggested maximum  
distance “X”: 36" (91.4 cm)  
Example vent system  
Calculating Vent System Length  
Wall cap  
6 ft (1.8 m)  
90 elbow  
To calculate the length of the system you need, add the  
equivalent feet (meters) for each vent piece used in the system.  
Vent Piece  
10" (25.4 cm) Round  
2 ft  
(0.6 m)  
45° elbow  
2.5 ft  
(0.8 m)  
The following example falls within the maximum recommended  
vent length of 35 ft (10.7 m).  
90° elbow  
5.0 ft  
(1.5 m)  
1 - 90° elbow  
1 - wall cap  
= 5.0 ft (1.5 m)  
= 0.0 ft (0.0 m)  
= 8.0 ft (2.4 m)  
8 ft (2.4 m) straight  
Maximum equivalent vent length is 35 ft (10.7 m).  
Length of system  
= 13.0 ft (3.9 m)  
Because Whirlpool Corporation policy includes a continuous commitment to improve  
our products, we reserve the right to change materials and specifications without notice.  
Dimensions are for planning purposes only. For complete details, see Installation  
Instructions packed with product. Specifications subject to change without notice.  
Ref. W10153187  
02-20-09  
 

AEG Vacuum Cleaner Z6160 User Manual
Aiphone Telephone R24 A User Manual
Airpura Industries Air Cleaner Airpura H600 User Manual
Allied International Camcorder GX1050 User Manual
Allied Telesis Network Router AR400 User Manual
Audiovox Automobile Electronics ACA200 User Manual
Avocent Switch SwitchView SC User Manual
Banner Stud Sensor MINI BEAM Expert User Manual
Banner Stud Sensor QS30 User Manual
Barco Camcorder H400 User Manual