2Wire Network Card third party wireless Ethernet adapters User Manual

Wireless Client  
Configuration Guide  
for third-party wireless Ethernet adapters  
 
 
Contents  
 
Wireless adapter configuration  
Introduction  
After your 802.11b wireless adapter is installed in your computer, you must configure it to communicate  
with the HomePortal. This guide describes how to configure the following wireless Ethernet (IEEE  
802.11b) adapters to operate with the HomePortal:  
Agere (ORiNOCO PC Card Silver or Gold)  
Cisco (Aironet 340 Series 11Mbps Wireless LAN Adapter)  
D-Link Air DWL-650  
Apple AirPort card  
Other third-party wireless Ethernet cards  
Note: The instructions for Agere, Cisco, and D-Link cards are for computers running Windows 98. The  
instructions for the Apple card are for computers running MacOS 9.0. Because not all Windows and  
Macintosh versions respond to new hardware in the same way, screens may appear in a different order and  
may have a slightly different appearance than the screens shown in these instructions.  
Locate the serial number and wireless encryption key  
Your HomePortal is configured with unique security parameters that must be configured into your wireless  
adapter.  
On the bottom of your HomePortal you will find two important pieces of information required for  
configuring your adapter: the serial number and the wireless encryption key.  
After you have located the serial number and wireless encryption key, perform the following steps to  
configure your wireless adapter.  
1
 
   
Agere ORiNOCO PC Card - Silver or Gold  
Consult the documentation provided with your wireless adapter to install the Agere ORiNOCO PC Card -  
Silver or Gold, then follow these steps:  
1. From the Start menu, select Programs > ORiNOCO > Client Manager.  
The ORiNOCO Client Manager screen appears.  
2. From the Actions menu, select Add/Edit Configuration Profile.  
3. The Add/Edit Configuration Profile screen appears.  
2
 
 
4. To create your profile, click Add. The Edit Configuration screen appears. Enter a profile name in the  
Profile Name field. The profile name identifies your wireless profile, and should be no more than 29  
characters in length.  
5. From the Network Type pulldown menu, select Access Point.  
6. To identify your network, click Next. The Edit Configuration screen appears.  
7. In the Network Name field, enter the word “2WIRE” followed by the last three digits of your  
HomePortal serial number, located on the bottom of your HomePortal. This is the Wireless Network  
Name. The Wireless Network Name is case-sensitive, so it is important that you enter the word  
2WIRE” in capital letters.  
3
 
8. Click Next. In the Set Security field, check the Enable Data Security checkbox. Verify that the Use  
Hexadecimal (0-9, a-f, A-F) radio button is selected.  
9. In the Key field, enter your ten-digit Wireless Encryption Key, located on the bottom of your  
HomePortal.  
10. Verify that Key 1 is selected in the Encrypt data with pulldown menu (this is the default).  
11. To select a power management option, click Next. The following screen appears.  
12. Select the power management option that you wish to use (the default is Off), and click Next.  
4
 
13. In the TCP/IP Behavior field, check the Renew IP Address when selecting this profile checkbox.  
14. Click Finish. The following screen appears.  
15. Click OK.  
5
 
Cisco Aironet  
Consult the documentation provided with your wireless card to install the Cisco Aironet adapter, then  
follow these steps:  
1. Double-click the Aironet Client Utility icon on your desktop. The Aironet Client Utility screen  
appears.  
2. Click the Profile Manager button. The Profile Manager screen appears.  
3. Click Add.  
4. In the Profile Management field, enter your profile name. The profile name identifies your wireless  
profile, and should be no more than 29 characters in length.  
5. Click Apply. The 340 Series Properties screen appears.  
6
 
 
6. Select the System Parameters tab. In the Client Name field, enter a client name. The client name  
identifies your PC.  
7. In the SSID1 field, enter the word “2WIRE” followed by the last three digits of your HomePortal serial  
number. This is the Wireless Network Name. The Wireless Network Name is case-sensitive, so it is  
important that you enter the word “2WIRE” in capital letters.  
8. In the Power Save Mode field, verify that the CAM (Constantly Awake Mode) radio button is selected  
(this is the default).  
9. In the Network Type field, verify that the Infrastructure radio button is selected (this is the default).  
10. Select the Network Security tab. In the WEP field, select the Use Static WEP Keys radio button.  
11. In the WEP Key Entry Method field, verify that the Hexadecimal (0-9, A-F) radio button is selected.  
12. In the WEP Key 1 field, select the Transmit Key radio button and enter your ten-digit Wireless  
Encryption Key, located on the bottom of your HomePortal.  
7
 
13. Click OK. The Profile Manager screen appears. Your profile name should now appear in the second  
line of the Profile Management field, indicating that your Cisco adapter is properly configured.  
14. Click OK.  
8
 
D-Link Air DWL-650  
Consult the documentation provided with your wireless adapter to install the D-Link Air DWL-650, then  
follow these steps:  
1. From the Start menu, select Programs > D-Link DWL-650 Control Utility > Configuration Utility.  
2. The D-Link Air DWL-650 Configuration screen appears.  
9
 
 
3. Select the Configuration tab.  
4. In the Mode field, enter Infrastructure.  
5. In the SSID field, enter the word “2WIRE” followed by the last three digits of your HomePortal serial  
number. This is the Wireless Network Name. The Wireless Network Name is case-sensitive, so it is  
important that you enter the word “2WIRE” in capital letters.  
6. In the Tx Rate pulldown menu, verify that Fully Automatic is selected (this is the default).  
7. In the PS Mode pulldown menu, verify that Disabled is selected (this is the default).  
8. Click Apply Changes.  
9. Select the Encryption tab.  
10. From the Encryption (WEP) pulldown menu, select 64 Bit.  
11. In the WEP Key Entry field, select the Manual Entry radio button.  
12. In the Key 1 field, enter your ten-digit Wireless Encryption Key, located on the bottom of your  
HomePortal.  
10  
 
13. From the Default Tx Key pulldown, select 1.  
14. Click Apply.  
15. Click OK.  
Apple AirPort card  
Note: Requires AirPort client software revision 2.0 or greater.  
Consult the documentation provided with your wireless adapter to install the Apple AirPort wireless  
adapter, then follow these steps:  
1. From the Apple pull-down menu, select AirPort to open the AirPort dialog box.  
2. In the AirPort Network panel, click the Choose Network pull-down menu.  
11  
 
 
3. Select your wireless network name. Your wireless network name is “2WIRE” followed by the last three  
digits of your HomePortal serial number, located on the bottom of your HomePortal.  
4. In the Password field, enter “$” followed by your ten-digit Wireless Encryption Key, located on the  
bottom of your HomePortal.  
5. Click OK.  
Other wireless Ethernet adapters  
Note: The following steps are completed using the configuration program provided with your wireless  
adapter. If you have not already done so, install the wireless adapter configuration software before  
continuing.  
1. Set the network type to Infrastructure. Refer to your wireless card documentation for instructions on  
editing the card’s network profile. Your wireless card should be configured to operate with an access  
point or residential gateway. This mode of operation is typically enabled by setting network type to  
Infrastructure.  
2. Set the wireless network name. The wireless network name of your HomePortal is 2WIRE in all capital  
letters, followed by the last three digit of the HomePortal serial number located on the bottom of your  
HomePortal. For example, if the last three digits of your HomePortal serial number are 102, your  
HomePortal network name would be 2WIRE102.  
The wireless network name is sometimes referred to as the Network Name, SSID, ESS ID, or Wireless  
LAN ID.  
12  
 
 
3. Enable wireless security. Your HomePortal is pre-configured to take advantage of wireless security.  
Referring to the instructions provided with your wireless card, enable wireless security.  
Wireless security is sometimes referred to as WEP (wired equivalent privacy), 64-bit encryption, or 40-  
bit encryption.  
4. Enter the encryption key. Once you have enabled security on your wireless card, you need to enter the  
unique security key for your HomePortal. To do this, set the network encryption type to hexadecimal,  
and enter your 10-digit wireless encryption key found on the bottom of your HomePortal.  
5. In general, accept your card’s defaults. The default value for the remainder of configurable settings for  
your network card should allow your wireless card to communicate with the HomePortal. Although the  
HomePortal is set by default to communicate using channel 6, it is not required to change your card to  
this setting as most cards will automatically detect the appropriate channel.  
Wireless configuration with Windows XP  
Note: The following steps are completed using the configuration program provided with Windows XP. If  
you have not already done so, install the wireless adapter configuration software before continuing. Make  
sure that the drivers for your adapter support Windows XP.  
Windows XP is designed to handle wireless configuration in a generic manner, provided that the  
manufacturer’s drivers support Windows XP.  
1. Right-click the Wireless Network Connection icon, located in the systray.  
2. Select View Available Wireless Networks.  
13  
 
 
3. The Connect to Wireless Network screen appears. In the Available networks field, select your wireless  
access point. The wireless access point displays as “2WIREin all capital letters, followed by the last  
three digits of the HomePortal serial number (located on the bottom of your HomePortal).  
4. In the Network key field, enter your ten-digit Wireless Encryption Key, located on the bottom of your  
HomePortal.  
5. Click Connect.  
6. A notification message now appears next to the Wireless Network Connection icon indicating that your  
wireless adapter is connected to your network.  
14  
 
5100-000059-000 Rev B  
 

321 Studiosr DMX5555z User Manual
Aarrow Fires Stove AFS1221 User Manual
Abocom Network Router P3102 4g User Manual
Acer Camcorder TCO03 User Manual
Agri Fab Lawn Sweeper 45 0337 User Manual
Altec Lansing Stereo Amplifier 1593C User Manual
Amcor Electric Heater AMH9 User Manual
American DJ Power Supply DP 20A User Manual
AVerMedia Technologies TV Receiver MCE 2005 User Manual
Eureka Tents Tent Timberline SQ Outfitter User Manual